Aussie 4 speed conversion.... how big is the factory hole?
I'm about to change my WB ute from a three on the tree to an aussie 4 speed. Does anyone have any advice about cutting the hole in the floor for the shifter? I was hoping someone could tell me the size...
View ArticleBoot size
Hey all.. Wanting to run 255/60/15's rear and 225's front on HQ ute lowered with Kings ultra low springs. Will I have dramas with clearance running this tyre size..?? Cheers Chris
View ArticleT700 Conversion to HQ - WB
anyone got some specs on the crossmember mods? looks to be in the same position as the T350. i have a T350 one here, but just before i swing motor and box in i wanted to double check... also, what is...
View ArticleShifter for Turbo 350
hey guy ive got a turbo 350 in my vl and ive got a b&m shifter in there. not hooked up yet. but was trying to keep the interior stock looking. what shifter will work with the auto.would say a...
View ArticleCrankshaft issue
Hey guys, I brought a 350 short block a while ago that had split a bore but had next to no miles on it. problem being that when I pulled it down someone has been there before me.......The crank is...
View Articlestroker kits
eBay Australia: Buy new & used fashion, electronics & home d Anyone had any dealings with these kits? Im not looking for a high revving strip motor, i just want it to be a tuff streeter!
View ArticlePuddleing problem ive got a quick fix
Hi just went through a very stressful rebuild on my hq wagon and when it was all too gether went to drive it and it was fueling up at full throttle now it was a new Holley 7448 with an adapter onto a...
View ArticleClik here to view.
Vic - holden vb commodore sle
i have a vb sle for sale, it has a 253 with a trimatic auto and extractors. it starts and drives well, but does need a good tune as it has been sitting around for quite a while. the body is very...
View Article308m8
Anyone know if you can get 14" round air filter for my impco 300a gas mixer setup. Currently uses 10 " but if u get a 14" then how and or where can you get an adapter plate or base to suit the bigger...
View ArticleCarb to efi conversion
Sorry if it's been posted before, My mate has a carb and a harrop single plane, msd 6al and a msd locked dizzy. Vn heads... What computer and hardware is required to convert it and is it possible to...
View ArticleHow can this be legal?
HT Monaro GTS V8 match firewall with its 3 tags, Sydney build RARE colour HK HG | eBay What scum bag would do this? as if there isnt some guy with a stolen monaro out there waiting for something like...
View ArticleVH Commodore
VH Commodore SL 3.3 blue auto extractors runs well manual steering rack good parts car $450 call 0422 822 546 in Eagleby.
View ArticleHQ under dash vents?
So ive got the entire bidy stripped of everything and ready to lift off the chassis and send to the blaster.... I have the smallest rust hole under my dash in the usual place near those vents on each...
View ArticleClik here to view.
FS: PERTH - 520rwhp s/charged VY Maloo
Series 1 Vy Maloo - build number 5 Extras include -Vortech v2 supercharged with tooth belt setup -Aftermarket Howard cam upgraded springs etc etc -60 pound injectors -Ase intercooler kit - black powder...
View Article308m8
Anyone know if you can get 14" round air filter for my impco 300a gas mixer setup. Currently uses 10 " but if u get a 14" then how and or where can you get an adapter plate or base to suit the bigger...
View ArticleFS: PERTH Vortech V1 T-trim 'race' kit *BRAND NEW*
Looking to sell a brand new vortech kit to suit Holden v8's Includes- V1 T-trim 'race' supercharger Vn-vs bracket kit including all bolts etc Gilmore/tooth belt pulley kit (13psi) Oil drain and feed...
View ArticleFS: PERTH VH Tunnel Rammed 355/t400
1984 sl/x ex chaser ...Unfinished project - has the following Good straight shell and paint(white)- group 3 kit minus boot spoiler and bonnet scoop Smoothed and painted Engine bay Custom trim Fuel cell...
View ArticleClik here to view.
little 330ci stroker what will she do ?
hi guys, built a 330 stroker, it dynod in at 464hp @7000 and 400ftlb on engine dyno (@flywheel), its in a VH commodore sedan. what do you think it will run at the strip? heres the specs: 330 cube...
View Article9'' ford diff gears
wanted 3.0-1 ratio must be quiet going in a street car what ya got thx 4 lookin
View ArticleClik here to view.
My First Car Worth Registering
I have been lurking around this forum for while finally decided that some of you guys would be interested in what I have been doing to my Ute recently. Sorry dont really have to many pics but ill find...
View Article