Does anyone know where to buy LS1 rocker studs in Aus?
As the title says. Im after a set of rocker studs for an LS1 but cant seem to find anywhere that sells them. Any help will be appreciated.
View ArticleViscous fan..VS..Thermo fan
Hi everyone, Just after an opinion or two on cooling. I have a stock original HQ 308 coupe auto run's cool etc. but hate the roar of the standard four blade fan set up at high rev's ....I don't really...
View ArticleClik here to view.
Dammit! Cast iron engine block repair. Help!
Ready to put in the new motor and found the pass side engine mount holes were stripped. OK, Put in some helicoil type repair kits. Went to tighten up the bracket and this happened. How can I fix this?...
View ArticleTubbing the rear end..
I'm sitting at work doing very little and I have had this great idea to tub the back end. I'm replacing the 10 bolt with a new 9'' so I could have that built to suit. I have the bare cab sitting in the...
View ArticleClik here to view.
383 stroker vs ute project.
Holden VS ute unfinished project. Engine specs: holden 304 block bored, clearanced, grout filled and prepped for 383, COME racing stroker crank, H beam rods, Set of probe forged pistons and Hastings...
View ArticleDifference between TP manifolds
What's the difference between the EFI and Carby versions of the various Torque Power manifolds? Do the "EFI" variants come with the injector bosses machined ready for injectors and hence the higher...
View Articleharmonic balancer install?
Hi all. Got a new balancer to throw on the 308, just don't know how to do it. Do u need a special instal tool to press it on or can u just do up the centre bolt and use that to pull it on? I've been...
View ArticleClik here to view.
06 maloo transmission coversion auto to manual
I have an automatic Z series Maloo which I have owned from new and now wish to convert to manual. Just wondering if anyone has attempted this before and any problems they ran into. Also what costs were...
View Articledizzy regraphing in adelaide
hi all I have a couple of 253/308 dizzys that need regraphing anyone recommend any one in Adelaide and what kind of mony would I be looking at ? cheers dean
View ArticleClik here to view.
F.S. or Swap Holden HJ Panel Van V8/manual
holden hj v8 panel van,3spd manual,3.08 salisbury diff.Suit project,has some rust,is missing upper rear tailgate/tailshaft plus some other bits and pieces roughly 80% there,gaurds are there and door...
View Articleengine rebuild
Hi this is my first use of this site i hope i am in right area. Have just rebuilt 308, engine want start blowing fuel & exhaust smoke out of carby. tried 2 x dizys, checked timing. has anyone got...
View ArticleClik here to view.
Worked 355 getting hot Help!!!!
Hey guys new on here so as much help would be great I've had a worked 355 built alloy heads forgies rods custom carby heavily ported heads 12.1 comp full ice ignition ect ect having a problem with...
View Articlehelp with 308
First time using this site hope i am in correct area. just rebuilt 308 trying to start motor but it keeps popping fuel & exhaust fumes out of carby, has anyone got any ideas what it could be thanks...
View Articleengine rebuild
Hi this is my first use of this site i hope i am in right area. Have just rebuilt 308, engine want start blowing fuel & exhaust smoke out of carby. tried 2 x dizys, checked timing. has anyone got...
View ArticleFactory Rocker covers
Just wanted to see what you guys are doing with the factory Vn rocker covers and the front breather ports. Has anyone removed the factory 90 degree elbows and fitted dash fittings or the likes to run...
View ArticleDropped a small screw down the dizzy hole
Hi all, I just dropped a small screw down the dizzy hole in my 308 ski boat motor. I can't see it with a torch. How can I find it? Will it be in the sump? Is it safe there? Any help/advice would be...
View ArticleTC and TE Cortina Tail lights and blinkers... Original Ford parts, worth...
Hey guys, I have an oldie relative who has a 2 sets of tail lights and blinkers. 1 from a TC and one from a TE.. They are old new parts. One of his neighbours is being a little persitant in wanting...
View ArticleClik here to view.
wtb Ameican alloy rim 15x10 ford bronco
380472_10200869588766866_2145019524_n.jpgim after 1 x 15 x10 American alloy rim the same as the ones on my bronco please pm me details if you have or know where i can get 1 i am in QLD (near ipswich)...
View ArticleHK Barrel Key Removal
I am trying to remove a barrel without the original key. I know about the small hole that you have to insert a suitable size tool into and compress the lock while turning the key but its not working....
View Article