Clik here to view.
Autogage "SMOKED SERIES" X 3 Guages
Hi All, I have the following 3 for sale. They are new in box and come with sender kits etc. Being the "smoked" series they are black until power hits them then they light up electronically. I was going...
View ArticleClik here to view.
WB Ute, Caprice T Trim supercharger, as new 5 spd TKO 600, 16inch HQ Simmons...
Most of this stuff is new with less hten 300 road kilometres in the last 8 years or so. PM or make offer - If no interest shown in car, it will be parted out. I think I can get close to what I'm asking...
View ArticleWB Ute caprice, Vortech T trim, 16" B45's (HQ), Tremec TKO 600 9" diff 31 spline
See the add under car sales for some photos. Have reciepts, most stuff is newish and may need a paint touch up here and there or a polish (for example the supercharger, aussie desert cooler burnout...
View ArticleClik here to view.
30mm clearance between chassis and rear rubber enough?
I'm measuring up my back end of my one tonner to get my diff shortened and wanted to make sure I've got enough clearance between my chassis and the rubber. I'm running a 4 link so I won't have all the...
View ArticleRESPRAY, Looking for painter BRISBANE
Hi all i have been looking for someone that does respays in Brisbane. On a budget so looking for someone that does this on the side etc. VT very straight no rust just bad paint fade. Looking at a few...
View ArticleGenuine HJ V8 holden panel van diff code query......
Hey guys,i got a genuine v8 hj panel van and on the id plate the code for the diff is GU4 and it runs a 3.08 salisbury open centre diff.Now my questions is i also have a 1980 VC commodore L with a 202...
View ArticleOverheating 308
My HQ 308 is overheaing?. Basically my guage will go up to 105 after 10 mins driving at around 2o degrees weather wise. Its all a bit strange. It will get hot then if I pull over urn engine off and...
View ArticleLifting out a 253 with Aussie 4 speed
Hey guy looking at pulling the engine out of the hx and was just wondering we're the best points are to lift of on a 253 I am also planing to leave gearbox attached as there is no front end on the car...
View Articleturbo choice for a 5 litre
Turbonetics Hurricane Turbochargers 11535 - SummitRacing.com calling people in the know! Help needed! I have had this idea of building a turbo setup for a 304, having played with cranky NA engines, the...
View ArticleWinton 300
I watched the Winton 300 on Speedweek today. What an entertaining series, I've never seen it before. There was a really interesting mix of cars. Future racers, EVO's, Hatchback Torana, BMW, Mazda,...
View Article350 Chev Fuel Filter with return
Hi all I've just purchased a 2 owner HQ Statesman Deville Factory 350. I am overhauling the original motor and i am having trouble getting my hands on a fuel filter to suit. It has the vapor tank...
View ArticleFlexplate damage
Hi I have just noticed that my flexplate as several half teeth sheered off. Would I be right in saying that this is caused from starter not disengaged correctly or could this be caused from a less...
View Article1 wire capable alternator
hi ,just got my 1 wire capable alt ,does this mean i just need to run a wire from the alt to the battery positive terminal and the alt will self excite or do i still need a alt light in there somehow...
View ArticleClik here to view.
Auto Euphoria 2012
Tuners across Melbourne converged on the Royal Melbourne show grounds over the weekend to check out Auto Euphoria and it certainly didnt disappoint. The two day event housed inside one of the...
View ArticleClik here to view.
QLD Holden 5.0 355 304 308 Engine components/parts brand new in box
For Sale! Block, Heads and Engine parts in box and brand new IMG_20120306_174527.jpgIMG_20121217_073351.jpgIMG_20121217_073255.jpg VS/VR Block has been soda blasted, chem cleaned, oil return valleys...
View Article10 bolt Salisbury - LSD gears the same as open centre ?
I'm considering a tru-trac upgrade for my 10 bolt Salisbury diff in the future, so was looking at swapping my 3.08 gears for 3.36 or 3.55 at same time as the current gears a bit tall for the cam...
View ArticleClik here to view.
brand new still in box sbc alloy heads 800 ono
up for sale is a set of procomp alloy heads part number pc3002a also supplied are matching intake gasket set to suit 64cc combustion chamber 190cc intake ports these have been beefed up when purchased...
View ArticleAU 6 seat wagon. QLD
Need to sell my AU Falcon wagon. Selling as is, one month out of rego. Good reliable car have driven it for 2 years, before that it belonged to a family member. Probably needs new shocks and...
View ArticleConvertor to flexplate gap?
Hi just wondering I have a gap of about 6 to 7mm between convertor and flexplate before bolting up is this ok or should I use shims washers to lesson the gap?
View Article